Parts

- 72mm long molded brake blocks with smooth post for common cantilever brakes

- Thermally bonded PTFE-coated slick galvanized cable for minimal friction - 2000mm

- Premium 31-strand stainless-slick low-friction rust-resistant cable - X-long 3000mm cables for non-traditional uses

- Premium 31-strand stainless-slick low-friction rust-resistant cable - X-long 3000mm cables for non-traditional uses

- Thermally bonded PTFE-coated slick galvanized cable for minimal friction - 1700mm

- Aluminum guides for securing housing/tubing to frame cable stops or cable guides

- Slotted aluminum barrel adjuster with backing nut for common brake levers

- 72mm long forged aluminum holder with hardware to fit most linear brakes - Replacement inserts include retention pins, fit most 72mm aluminum holders

- Lightweight stainless steel rotor, Great for all-Mountain or enduro use - International standard 6-Bolt 44mm bcd rotor mounting. 95/112/154G

- Ultralight stainless steel rotor, ideal for XC use - International standard 6-Bolt 44mm bcd rotor mounting. 56/70/82G

Gecko Grip is EVA foam and ventilated polyurethane in a laminated, layered construction. Gecko Grip has a rubbery, "grippy" feel compared to cork tape. It lays flat on the wrapped bars and is thinner than cork. It doesn't absorb sweat as easily as cork and can be wiped off with a wet rag in seconds.

Rubber Gecko is a cushy bar tape made with foam and an outer layer of natural rubber. Rubber Gecko offers a soft tactile grip with a bit of give to it. It wraps slightly fatter than our original gecko grip, but not by much. Perfect for the rainy, cold cobbled classics.

Art Gecko is our new grippy polyurethane rubber bar tape with a colorful artistic patter on the drops. This pattern is called a tri-color tessellation. When wrapped from the bottom it fades to black about where the brake levers mount. - Artistic pattern, 9 colorful choices - Color below the drops, black up top - Great feel, Polyurethane rubber surface - 220 cm rolls, plenty of length - Nice flat wrap - 92 grams including the plugs

- 90 degree

- Noodle/Boot completely seal brake cable, upgrades most linear brakes

Disc Brake Adapters

- Replacement barrel adjuster for FR5 and SD7 levers - Includes one pair

Attach your IS Mount disc brake brackets with premium SRAM mounting bolts. These bolts are made from stainless steel for a lifetime of use and come with thread-locking compound already applied.

Bolt on Avid's 20R Brake Pads for consistent, powerful braking. They're designed for use with linear-pull brakes.

Slip Avid's Rim Wrangler 2 Brake Pad Inserts into your Rim Wrangler 2 cartridges (sold separately) for excellent braking no matter the conditions. The easy-to-use cartridge design makes swapping pads a breeze. They're designed for use with linear-pull brakes.

The squeeze of our levers is what dreams are made of. Most of our levers can be swapped to be run either front or rear, which is convenient if you like to your brakes reversed and a Godsend if you bust a lever in the middle of the woods. Avid levers are easy to install, simple to set up, and a pleasure to pull. - ReachAdjustment -- Qwik-Adjust Barrel Adjuster Bend Zone

Avid makes it easy to get a perfectly set up brake with their innovative CPS Hardware Kit. Each kit features a series of washers that make it easy to set up your brake. Step 1: Install the bolts and washers loosely so the caliper can move. Step 2: Squeeze the brake lever. Step 3: Tighten the bolts. It's that simple to get a rub-free setup! This kit includes stainless steel hardware with washers and bolts for both CPS (Caliper Positioning System) mounting and standard (direct-mount)mounting.

To keep your Avid brakes functioning properly, check your pads for wear and replace them when necessary. Organic compound pads are softer for quieter braking and increased modulation, while metallic pads dissipate heat better and last a bit longer. Two pads, one retraction spring and a mounting bolt are included (enough for one brake) in each pad set. And, choose an aluminum backing plate if you're really counting the grams.

Slip Avid's Shorty Brake Pad Inserts into your Shorty cartridges (sold separately) for excellent braking no matter the conditions. The easy-to-use cartridge design makes swapping pads a breeze.

Built around one of our original breakthrough designs, the Speed Dial 7 is the smooth and powerful way to control linear-pull or mechanical disc brakes. They are super easy to install and adjust so you can dial in the modulation just the way you like. - Compatible with mechanical disc brakes and linear-pull brakes. - Reach Adjust and Speed Dial Leverage Adjust - Reversible

The squeeze of our levers is what dreams are made of (and you know which dreams we're talking about). Most of our levers can be swapped to be run either front or rear, which is convenient if you like to your brakes reversed and a Godsend if you bust a lever in the middle of the woods. Avid levers are easy to install, simple to set up, and a pleasure to pull. - Reach Adjustment - Qwik-Adjust Barrel Adjuster - Compatible with mechanical disc brakes and linear-pull brakes

- Includes stainless bolts - Fits 160mm front and 140mm rear rotors

To keep your Avid brakes functioning properly, check your pads for wear and replace them when necessary. Organic compound pads are softer for quieter braking and increased modulation, while metallic pads dissipate heat better and last a bit longer. Two pads, one retraction spring and a mounting bolt are included (enough for one brake) in each pad set. And, choose an aluminum backing plate if you're really counting the grams.

To keep your Avid brakes functioning properly, check your pads for wear and replace them when necessary. Organic compound pads are softer for quieter braking and increased modulation, while metallic pads dissipate heat better and last a bit longer. Two pads, one retraction spring and a mounting bolt are included (enough for one brake) in each pad set. And, choose an aluminum backing plate if you're really counting the grams.

Avid's Front 170mm Post Bracket Hardware Kit has everything you need to mount a 170mm rotor (sold separately) to the front of your bike. Kits include mounting bolts and post mount spacers for front brake installation.